Every heating repair call includes a full diagnostic, not just a parts swap. Here is what is covered in a standard visit, and what we quote separately if your system needs it.
Thermostat call verification, control board fault codes, ignitor or reversing valve test, capacitor microfarad readings, blower amp draw, and refrigerant pressure check on heat pumps. We find the actual fault, not the nearest symptom.
Capacitors, contactors, ignitors, blower motors, control boards, and thermostats are stocked on the truck and replaced on the spot. We use OEM-spec or better parts and verify operation after install.
If the system is low on R-410A or R-32, we locate the leak with an electronic detector, repair the joint or component, evacuate with a vacuum pump, and recharge by weight with a refrigerant scale. No top-off without a leak search.
A clogged PVC drain line is one of the most common no-heat causes in Florida. We clear the line, flush it, and treat it to slow biological growth. We also check the float switch so it does not trip again next month.
We inspect the air filter, blower wheel, and evaporator coil for restriction. A dirty filter or a fouled coil overheats the system and trips the limit switch. Restoring airflow often fixes the problem on its own.
We run a full heating cycle and measure temperature rise at the supply registers. If the numbers are not in spec, we keep working. Nothing gets signed off until the system proves it is heating correctly.
Heating repair Orlando FL is the diagnostic and repair work that restores heat to your home when a furnace, heat pump, or air handler stops producing warm air. That means testing the thermostat call, checking the ignitor or reversing valve, reading refrigerant pressures on manifold gauges, and confirming the blower motor and capacitor are pulling correct amps. We do not guess. We test, we find the fault, and we fix the part that failed.
Orlando winters are mild but not harmless. Overnight lows in the 30s and 40s hit hard on homes built for cooling, and heat pumps that ran all summer finally show their wear in December. If your heater is not working, repair is usually cheaper than replacement - and faster. We stock capacitors, contactors, and blower motors on the truck so most calls close in one visit, including emergency heater repair Orlando requests after a cold front rolls through.
No mystery, no runaround. Here is how a heating repair call goes from the moment you pick up the phone to the moment your house is warm again.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Manifold gauges
Used to read high-side and low-side refrigerant pressures on heat pumps. Pressure readings tell us whether the system is undercharged, overcharged, or has a restriction in the circuit.
Multimeter and clamp meter
We measure capacitor microfarads, control board voltage, and blower motor amp draw. A capacitor that reads 20 percent below its rated microfarads is failing, even if it still starts the motor.
Electronic leak detector
Finds refrigerant leaks at joints, Schrader ports, and coil tubing. We use it before any recharge so we are not topping off a system that will leak down again in a month.
Vacuum pump and recovery machine
Any repair that opens the refrigerant circuit requires recovery, evacuation, and a proper recharge. We pull a deep vacuum to remove moisture before charging by weight with a refrigerant scale.
Fin comb and tube cutter
Used to straighten bent coil fins and to cut copper line set cleanly when a section needs replacement. Clean cuts mean better flares and fewer future leaks.
EPA Section 608 refrigerant handling
Every tech who touches refrigerant holds EPA Section 608 certification. That means legal recovery, proper evacuation, and charging by weight - not by gauge guess. It also means your system leaves with the correct charge, which protects the compressor.
NATE-certified diagnostics
Our technicians hold NATE certification, which requires passing exams on heat pump and furnace troubleshooting. That training shows up in the diagnostic sequence: we test in order, from thermostat to control board to motor, instead of swapping parts until something works.
ACCA standards for airflow and load
We follow ACCA standards for airflow verification and system performance. That means checking static pressure, temperature rise, and duct sizing when a system is not performing. It is how we catch duct problems that look like equipment problems.
AHRI-matched parts and systems
When we replace a component or quote a new system, we use AHRI-certified matched combinations. That protects your manufacturer warranty and ensures the equipment performs to its rated efficiency instead of falling short.
01
What we do: We dispatch same-day, test the auxiliary heat strips and reversing valve, and confirm the system is switching to heat mode correctly. If the heat strips are not engaging, we repair the sequencer or control board.
→ The house holds temperature through the cold snap instead of falling 10 degrees overnight. You wake up to a warm house and a system that is running in spec.
02
What we do: That smell is usually dust burning off the heat strips, but it can also be a failing blower motor or a wiring issue. We inspect the blower, the wiring, and the control board, and we test amp draw on the motor.
→ You get a clear answer on whether it is normal first-run dust or a real fault. If a part is failing, we replace it before it becomes a no-heat call in the middle of the night.
03
What we do: We diagnose the reversing valve, defrost board, and refrigerant charge. If the valve is stuck, we repair or replace it. If the charge is low, we find and fix the leak before recharging.
→ Heat is restored the same day, and the system runs a full heating cycle without dropping back into cool mode. You get a written summary of what failed and what we replaced.
04
What we do: We run 24/7 emergency dispatch, so a tech is sent even on holidays. We diagnose on-site, repair with parts from the truck, and send you a clear invoice you can forward to the owner.
→ The tenant has heat the same day, and you avoid a habitability complaint. You get documentation of the repair for your records.
Orlando heating repair is different from heating repair in most of the country. The vast majority of homes here heat with a heat pump, not a gas furnace, and that heat pump runs almost year-round. By the time winter arrives, the system has already logged 10 or 11 months of cooling duty. That is why the failures we see most are reversing valves stuck in cool mode, defrost boards that never complete a cycle, and auxiliary heat strips that fail to engage when the outdoor temperature drops into the 30s. Florida's humidity adds another layer. Condensate drain lines grow biological film fast, and a clogged PVC drain will trip a float switch and shut the system down even when the heat itself is fine. Attic duct systems take a beating too - flex duct and duct insulation degrade in 140-degree attic heat, and leaks that did not matter in summer become obvious in winter when the system cannot keep up. We work to Florida HVAC license requirements and pull permits when the job calls for it. If you are searching for affordable heating repair Orlando FL 32801 or anywhere in Orange County, we are set up to diagnose heat pump faults fast and fix them the same day. Cold snaps here are short but sharp, and a system that fails on night one needs to be running by night two.
Most no-heat calls trace back to a handful of failures. Here are the ones we see most often in Orlando, and what happens if you let them ride.
Problem
A stuck reversing valve or a failed defrost board leaves you running the cooling cycle in January. The house gets colder the longer the system runs, and the compressor takes unnecessary wear.
Our Fix
We test the reversing valve solenoid and defrost board, confirm the refrigerant charge, and repair or replace the failed component. Most reversing valve repairs are done in a single visit with the system back to heating within hours.
Problem
Short cycling spikes your power bill, wears out the compressor, and never lets the house reach temperature. It is often a sign of an oversized system, a failing thermostat, or a refrigerant charge issue.
Our Fix
We check thermostat calibration, refrigerant pressures, and airflow. If the system is overcharged or undercharged, we correct the charge by weight. If the thermostat is the culprit, we replace it with a properly configured smart model.
Problem
A dirty filter or a failing blower motor causes the system to overheat and trip the safety limit. The system shuts down to protect itself, and it will keep tripping until the airflow problem is fixed.
Our Fix
We replace the filter, inspect the blower wheel and motor, and test amp draw. If the motor is drawing over spec, we replace it. Restoring airflow stops the limit trips and gets heat back on.
Problem
A frozen coil blocks airflow and can send liquid refrigerant back to the compressor, which is a costly failure. It usually points to low refrigerant charge or a restricted filter.
Our Fix
We thaw the coil, run a leak search with an electronic detector, repair the leak, and recharge the system by weight. We also verify the filter and ductwork are not restricting airflow before we leave.
A failed heater is a comfort problem, a safety problem, and often a money problem. Here is what you get when you book heating repair with us.
Same-day heat restored
Most heating repair calls are finished in two to four hours. We carry the common failure parts - capacitors, contactors, ignitors, blower motors - so you are not waiting three days for a second visit. Book before noon and you will likely sleep warm that night.
Upfront pricing, no surprises
You get the diagnosis and the price before we start. Typical 2026 heating repair in Orlando runs $180 to $650 depending on the failed component and whether refrigerant work is involved. No hidden trip charges, no pressure to replace a system that only needs a $40 part.
Licensed, EPA-certified techs
Every technician holds a Florida HVAC license and EPA Section 608 certification for refrigerant handling. We work to ACCA standards and pull permits when the job requires it. That matters when you sell the house and an inspector asks who touched the system.
Heat pump specialists
Most Orlando homes heat with a heat pump, not a gas furnace. We diagnose reversing valve failure, defrost board faults, and auxiliary heat strips that never engage. If your system blows cool air in heat mode, we know exactly where to look.
Google ★★★★★4.9
Called on a Saturday morning with no heat and a house full of kids. Tech was here by noon, diagnosed a failed blower motor, and had the part on the truck. Heat was back by 2 p.m. Fair price, clean work, no upsell.
Yelp ★★★★★4.8
Our heat pump was blowing cold air and another company told us we needed a new unit. These guys found a stuck reversing valve, repaired it, and saved us thousands. Honest diagnosis and clear explanation of what failed.
BBB ★★★★★4.9
We manage several rental properties in Orlando and have used this company for heating and cooling repairs for years. Same-day service, clear invoices, and they always text when they are on the way. Reliable.
Google ★★★★★5.0
Emergency call at 11 p.m. in January. Live person answered, tech dispatched, capacitor replaced, heat restored. I expected a huge after-hours bill and it was reasonable and quoted upfront. Will use again.
Real experiences from customers who chose our Heating Repair services.
“Our heat pump quit on a Friday night in January and the house was down to 58 by morning. I called at 7 a.m. and a tech was here by 10. He found a failed run capacitor and a clogged drain line, had both parts on the truck, and we had heat by lunch. Price was exactly what he quoted. No games.”
Marcus T.
Homeowner, College Park
“Our Trane system was blowing cool air in heat mode and two other companies told us we needed a new unit. Orlando HVAC Air Conditioning diagnosed a stuck reversing valve, repaired it for a fraction of replacement cost, and it has run perfectly through two winters since. Honest diagnosis saved us thousands.”
Priya R.
Homeowner, Lake Nona
“I manage six rental units and heating calls are always urgent. This team has handled three no-heat calls for me this year, all same-day, all with clear invoices I can forward to owners. They text when they are on the way and they clean up after themselves. That is rare.”
Dana W.
Property Manager, Winter Park
Real answers to the questions we hear most often from local homeowners and property managers.
Most Orlando homes heat and cool with the same heat pump. When we repair your heating side, we also check the cooling cycle - refrigerant charge, reversing valve, and contactor - so you are not calling us back in May.
View AC RepairOur emergency dispatch runs year-round. The same techs who handle 2 a.m. heating calls in January handle 2 a.m. cooling calls in July. One number, one team, no seasonal gaps in coverage.
View Emergency AC RepairIf your heat pump is 15 years old and the compressor has failed, repair may not make financial sense. We quote replacement with AHRI-certified matched systems and handle the permit and haul-away.
View AC Installation & ReplacementA fall tune-up catches the capacitor that is about to fail and the drain line that is about to clog. It is the cheapest way to avoid a no-heat call in December. We recommend one visit each spring and fall.
View AC Maintenance & Tune-UpsHeat pumps are the dominant heating system in Orlando, and they fail differently than gas furnaces. We service reversing valves, defrost boards, auxiliary heat strips, and refrigerant circuits on every major brand.
View Heat Pump ServicesMitsubishi Electric and Daikin mini-splits heat and cool individual rooms. When a head stops producing heat, the fault is often a clogged filter, a low refrigerant charge, or a communication error between the head and the outdoor unit.
View Ductless Mini-SplitsCall us any time, day or night, and a live dispatcher will schedule your visit. We run same-day appointments across Orlando and the surrounding communities, and we answer the phone 24/7 for emergencies. Reach us at 689 315 0679 or send an email and we will get back to you fast.
Phone
689 315 0679Address
6000 N Orange Blossom Trl, Orlando, FL 32808
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available
